Ithaca Model 37 Schematic

Moderator: ripjack13

User avatar
Administrator
Posts: 667
Joined: Tue May 31, 2011 9:19 pm
Location: New York
PostPosted: Thu Dec 22, 2011 3:33 am
Image
Ithaca Model 37 Schematic

Copper BB
Posts: 3
Joined: Sun Mar 11, 2012 3:03 am
PostPosted: Thu Mar 22, 2012 1:33 am
WHAT years of production???
User avatar
.270 WIN
Posts: 422
Joined: Thu Feb 23, 2012 5:21 pm
Location: phila pa
PostPosted: Thu Mar 22, 2012 9:11 am
all

.270 WIN
Posts: 146
Joined: Thu Nov 10, 2011 2:10 pm
Location: S.E. Va. CSA
PostPosted: Thu Mar 22, 2012 9:13 am
To add to what twistedoak said from 1937 to present.
User avatar
Vendor
Posts: 967
Joined: Fri Sep 09, 2011 5:06 am
Location: Mobile, AL
PostPosted: Thu Mar 22, 2012 4:34 pm
the only really big internal difference between the new ones and the old ones is part 21. the new ones is a pin and the old ones is a really tiny screw. and I have gotten to be a really big fan of that pin.

otherwise the schematic applies to them all
--Jim

.270 WIN
Posts: 429
Joined: Sat Jan 21, 2012 8:50 am
PostPosted: Thu Mar 22, 2012 6:29 pm
ravengunsmith wrote:the only really big internal difference between the new ones and the old ones is part 21. the new ones is a pin and the old ones is a really tiny screw. and I have gotten to be a really big fan of that pin.

otherwise the schematic applies to them all


Best I can tell the screw was changed to a pin in the mid 70s. I have a 37 from 1974 with the screw, and a 37 from 1977 with the pin. I think that the pin idea was a carry over from the model 51. If you take one of them apart you will find like pins. It was most likely cost savings. Saving time from threading the hole and making or buying those tiny screws. I have never had a problem with one of those screws and I sure hope I don't. If one of those got stuck it would be a bear to get out.

Also keep in mind that a few of the parts like the lifter would be different (longer) for a 3 inch gun.
Last edited by 1977cutcher on Thu Mar 22, 2012 7:23 pm, edited 1 time in total.

.270 WIN
Posts: 146
Joined: Thu Nov 10, 2011 2:10 pm
Location: S.E. Va. CSA
PostPosted: Thu Mar 22, 2012 6:31 pm
I forgot to add unless you find an untouched gun with the serial number starting in 38 then part 13 would be different.
User avatar
.270 WIN
Posts: 422
Joined: Thu Feb 23, 2012 5:21 pm
Location: phila pa
PostPosted: Thu Mar 22, 2012 11:01 pm
the hammers can either be spurred or unspurred too
that and the tang on the trigger blocks are 2 sizes
User avatar
Vendor
Posts: 967
Joined: Fri Sep 09, 2011 5:06 am
Location: Mobile, AL
PostPosted: Fri Mar 23, 2012 6:46 am
twistedoak wrote:the hammers can either be spurred or unspurred too
that and the tang on the trigger blocks are 2 sizes



That's right, I forgot about the hammer,
--Jim
User avatar
Vendor
Posts: 967
Joined: Fri Sep 09, 2011 5:06 am
Location: Mobile, AL
PostPosted: Fri Mar 23, 2012 6:51 am
1977cutcher wrote:
ravengunsmith wrote:the only really big internal difference between the new ones and the old ones is part 21. the new ones is a pin and the old ones is a really tiny screw. and I have gotten to be a really big fan of that pin.

otherwise the schematic applies to them all


Best I can tell the screw was changed to a pin in the mid 70s. I have a 37 from 1974 with the screw, and a 37 from 1977 with the pin. I think that the pin idea was a carry over from the model 51. If you take one of them apart you will find like pins. It was most likely cost savings. Saving time from threading the hole and making or buying those tiny screws. I have never had a problem with one of those screws and I sure hope I don't. If one of those got stuck it would be a bear to get out.

Also keep in mind that a few of the parts like the lifter would be different (longer) for a 3 inch gun.



I don't know if it was cost savings or not, but I like that pin over the screw. You can work it loose alot more easily that you can the screw. I've had to feather a couple of them out because some yahoo tried to take it out using god knows what. And this will be one of the VERY few times you will ever hear me say I prefer a pin over a screw.
--Jim
User avatar
Vendor
Posts: 967
Joined: Fri Sep 09, 2011 5:06 am
Location: Mobile, AL
PostPosted: Fri Mar 23, 2012 6:52 am
Chuck Findley wrote:I forgot to add unless you find an untouched gun with the serial number starting in 38 then part 13 would be different.



What changed in the carrier, Chuck?
--Jim

.270 WIN
Posts: 146
Joined: Thu Nov 10, 2011 2:10 pm
Location: S.E. Va. CSA
PostPosted: Fri Mar 23, 2012 7:15 am
It wasn't much of a change, spurs on the carrier. It was supposed to help with ejecting the spent shell. The carrier was changed back. However, you will find spurs on the shell carrier on several guns made after that.

There was something else about the 38 serial number range guns. I will have check on that and get back.
User avatar
Vendor
Posts: 967
Joined: Fri Sep 09, 2011 5:06 am
Location: Mobile, AL
PostPosted: Fri Mar 23, 2012 7:22 am
Chuck Findley wrote:It wasn't much of a change, spurs on the carrier. It was supposed to help with ejecting the spent shell. The carrier was changed back. However, you will find spurs on the shell carrier on several guns made after that.

There was something else about the 38 serial number range guns. I will have check on that and get back.



hey thanks for the info, Chuck!
--Jim
User avatar
.270 WIN
Posts: 422
Joined: Thu Feb 23, 2012 5:21 pm
Location: phila pa
PostPosted: Fri Mar 23, 2012 8:14 am
the carriers hes talking about were basicly all recalled ,and they were replaced with the standard carrier.

if you find a 38 with the spurred carrier its a pretty rare piece,as most were retrofitted.


also on early (real)early m37s they used only 1 extractor (top i think) and very quickly a 2nd was added all singlr extractor guns were recalled and retrofitted the 2nd extractor.
and early m37 with a single extractor is also extreamly rare to find
User avatar
Vendor
Posts: 967
Joined: Fri Sep 09, 2011 5:06 am
Location: Mobile, AL
PostPosted: Fri Mar 23, 2012 11:56 am
I am having a vision of what spurs on the carrier could do to paper hulled shells.....
--Jim

.270 WIN
Posts: 146
Joined: Thu Nov 10, 2011 2:10 pm
Location: S.E. Va. CSA
PostPosted: Fri Mar 23, 2012 6:37 pm
Actually there are other differences in the guns marked with the 38 prefix (1975). besides the carriers
The shell stops were different and the action bar was notched to allow this to work. The new system was supposed to eliminate the hand fitting required.

This didn't work and all of the guns with the 38 prefix were recalled and repaired. If you should find one that has not been touched it is very very rare.

The topless extractor models my friend from Pennsylvania is talking about is is really really early. A left over from the parent gun the Remington 17. From what I have read there is only one left serial #2023.
Last edited by Chuck Findley on Sat Mar 24, 2012 8:46 am, edited 1 time in total.

.270 WIN
Posts: 429
Joined: Sat Jan 21, 2012 8:50 am
PostPosted: Fri Mar 23, 2012 8:17 pm
I have often wondered why Ithaca had problems with out the top extractor. My model 17 has always worked fine. I wonder if it was because the 12 gauge shell is bigger and harder to extract (the 17 was made in 20 only. Any guesses?
User avatar
Vendor
Posts: 967
Joined: Fri Sep 09, 2011 5:06 am
Location: Mobile, AL
PostPosted: Sat Mar 24, 2012 4:12 am
Well, a 12 ga shell is heavier and that extra weight could cause a shell to drop prematurely. the other one could be swollen hulls which might cause the extractor to slip
--Jim

.270 WIN
Posts: 146
Joined: Thu Nov 10, 2011 2:10 pm
Location: S.E. Va. CSA
PostPosted: Sat Mar 24, 2012 7:59 pm
I don't know serial #2023 dates to 1937. So the double extractors is an improvement on the original design.

.270 WIN
Posts: 429
Joined: Sat Jan 21, 2012 8:50 am
PostPosted: Sun Mar 25, 2012 10:21 am
Chuck Findley wrote:I don't know serial #2023 dates to 1937. So the double extractors is an improvement on the original design.

Their where 3500 guns made in 1937 starting with serial number 1. I have 2 first year production guns one in the 7xx range and one in the 25xx range. Both have been "updated" to the double extractors. From time to time I come across other first year guns on Gun Broker and they all seem to be updated as well. My guess is that they most likely updated all but a handful of them.

.270 WIN
Posts: 146
Joined: Thu Nov 10, 2011 2:10 pm
Location: S.E. Va. CSA
PostPosted: Mon Mar 26, 2012 10:47 am
1977cutcher wrote:
Chuck Findley wrote:I don't know serial #2023 dates to 1937. So the double extractors is an improvement on the original design.

Their where 3500 guns made in 1937 starting with serial number 1. I have 2 first year production guns one in the 7xx range and one in the 25xx range. Both have been "updated" to the double extractors. From time to time I come across other first year guns on Gun Broker and they all seem to be updated as well. My guess is that they most likely updated all but a handful of them.


I would agree, like I said before from what I have read (Mr Snyder's book) only the one remains with the single extractor. There could be more its anyones guess.
User avatar
Vendor
Posts: 967
Joined: Fri Sep 09, 2011 5:06 am
Location: Mobile, AL
PostPosted: Mon Mar 26, 2012 12:18 pm
Chuck Findley wrote:
1977cutcher wrote:
Chuck Findley wrote:I don't know serial #2023 dates to 1937. So the double extractors is an improvement on the original design.

Their where 3500 guns made in 1937 starting with serial number 1. I have 2 first year production guns one in the 7xx range and one in the 25xx range. Both have been "updated" to the double extractors. From time to time I come across other first year guns on Gun Broker and they all seem to be updated as well. My guess is that they most likely updated all but a handful of them.


I would agree, like I said before from what I have read (Mr Snyder's book) only the one remains with the single extractor. There could be more its anyones guess.



If there is another I would bet that a) you could auction it off for a very healthy figure and b) the person who would own it, would have NO idea what he has.
--Jim
User avatar
.270 WIN
Posts: 422
Joined: Thu Feb 23, 2012 5:21 pm
Location: phila pa
PostPosted: Mon Mar 26, 2012 3:00 pm
along the thought of people and guns they have no idea about

i think about how many gorgeous guns have been melted down in them "guns for nike sneaker " deals
that PDs often hold
User avatar
.270 WIN
Posts: 422
Joined: Thu Feb 23, 2012 5:21 pm
Location: phila pa
PostPosted: Thu Mar 29, 2012 1:00 pm
i just noticed my 75 starting with 371 has a spurred carrier in it

.270 WIN
Posts: 146
Joined: Thu Nov 10, 2011 2:10 pm
Location: S.E. Va. CSA
PostPosted: Thu Mar 29, 2012 3:19 pm
twistedoak wrote:along the thought of people and guns they have no idea about

i think about how many gorgeous guns have been melted down in them "guns for nike sneaker " deals
that PDs often hold


I know exactly how you feel. For the sake of not opening another can of worms I will refrain from further
comment.

twistedoak wrote:i just noticed my 75 starting with 371 has a spurred carrier in it


If memory serves the 38 prefix dates to 75. Ithaca used the old style or spurred carriers through out the mid to late 70s. Remember, the company was going through bankruptcy around this timeframe.

Besides, most factory shells were plastic. So the spurs were not really to much of an issue.
Next

Return to Ithaca Model 37

Who is online

Users browsing this forum: No registered users and 3 guests

cron